Your cart is empty

Neck Glueup Tutorial

4Neck Assembly JigThe simplest and most efficient way to glue up an acoustic guitar neck is with the use of a Neck Assembly Jig.

Using this jig you can cut your neck blanks to size, cut the scarf joint very accurately, and glue the headpiece and the heel blocks at the same time.

A bit of background needs to be addressed. If you wish to give your acoustic guitar neck the ultimate in strength and bending resistance be sure to review our chapters on static neck reinforcement, properties of wood in neck construction, and adjustable truss rods.

Since wood for guitar necks tends to be quite costly, and if you are new to guitar construction, it may be a good idea for you to follow this procedure with a scrap piece of wood rather than ruining a $25 piece of neck stock.

This is our Neck Assembly Jig for 6 and 12 String Acoustic Guitars
 
One Piece Neck Construction Using The Neck Assembly Jig

In order to get the most out of your neck stock, be sure to square up the piece of neck stock before you start the construction process. Usually a piece of neck stock will measure about 3” x 36” x 7/8” thick (75mm x 900mm x 22mm). Place the entire length of neck stock into the jig if possible with the end tight against the end closure. Clamp the stock in place with a couple of quick-release clamps and make sure the bottom of the stock is flat against the jig bottom. Install the miter slot guide bar and run it slowly through the band saw. Keep your feed rate slow and consistent with only forward force and no sideways pressure. The quality of your scarf joint will only be as good as your band saw setup, so be sure to check the squareness of the blade to table before you start the cut. Also double check the blade tension. (Note: if you wish to construct a laminated wood neck - see the instructions that follow this section).

Upon making the scarf joint cut, the head piece needs to be cut to length. First mark out the thickness of the headpiece on the cutoff you just removed from the jig. When you determine the proper headpiece length, cut the headpiece from the cutoff wood. Next cut the headpiece to the proper thickness using a band saw. Finish sand the headpiece surfaces as needed.
Even though the saw-cut from the band saw may be very smooth, it does need to be sanded smooth for a proper glue joint as this joint receives a lot of prying force from the guitar strings. I choose to do this on a stationary belt sander, but it can easily be completed on a large sanding surface as well such as a piece of marble or corian countertop with adhesive sandpaper attached to the surface.

With the neck stock still loaded in the jig, insert the headpiece into the jig with the angled face of the cut facing up toward the fence. Mount the heel block retainer in place and cut the heel blocks to length from the cutoff portion of the headpiece. Note that there is one of the heel blocks that is longer and that piece is mounted directly to underside of the neck.

Size and glue your headpiece veneer sandwich, if you are going to add that detail to your guitar. There are many options that you can use to add this very attractive detail to your handmade guitar.

The Neck Assembly Jig in ActionNeck Glue Up

Mount the headpiece retainer for the 6 or 12 string guitar neck. Dry fit the headpiece to the neck and check with clamps. Also dry-fit the heel blocks. Make sure that they fit snug between the side fence of the jig and the heel block retaining block. At this time it is a good idea to flip the heel block to have every blocks' grain running opposed to the one below. This will minimize any warping and cracking of the heel.


If all looks well, glue all blocks in place using the clamping cauls to prevent denting of the stock. Note that is is a good idea to place waxed paper beneath the neck prior to gluing to minimize cleanup and damage to the jig.



Here is the Neck Assembly Jig in clamping mode for the guitar headpiece -
 6 string acoustic guitar in this case.After removal from the jig, sand the
sides of the neck to square them up to facilitate neck channeling for
reinforcement bars and or an adjustable truss rod.


Laminated Neck Construction Using The Neck Assembly Jig



Run Grain If you intend to construct a laminated neck by using multi-laminations of wood, follow these instructions while using the Neck Assembly Jig.

In order to obtain the best and most warp resistant neck construction, you should arrange the neck wood so each half of the neck grain of each half of the neck stock runs in opposite directions (refer to illustration). By doing this we are using the properties of woods' ability to shrink and contract and have these forces create an even stronger, more warp-resistant neck that you can obtain with a single-piece vertical piece of wood. I have always constructed by necks this way and have experiences very few problems with warping.

(Note: if you wish to have the laminations run continuously from the neck into the headpiece, you have to complete this task prior to cutting the scarf joint in order to best align the laminations.) Also, to keep things aligned, cut each half of the neck wood exactly the same with. This will make it easy to line up the laminated wood pieces in the Neck Assembly Jig.

Bottom illustration shows neck wood prior to ripping.
Upper illustration shows neck with proper alignment
of wood grain for the assembled neck.to length and
rip it down the middle with the sawing method of
your choice. Because we will be adding a lamination
to the neck it will increase the width of the neck, and the
 kerf cut of the saw blade is not a concern.


Laminated NeckCut the neck

I prefer to use a table saw for this operation. To obtain this grain pattern you will have to flip one of the pieces of neck stock around. This is most easily done by looking at the freshly cut end grain. Finally cut the center strip or or

 
 
After the neck laminations are dry, square-up all sides and sand smooth. Lastly, the neck width has to match the width of the original wood blank (about 3”). Measure the difference in width from the laminated neck and the remainder of the headstock and split the difference. Cut this amount from each side of the neck to match them up correctly.


Be sure to use plywood clamping cauls to protect the neck wood from denting during clampingPlace the laminated neck into the Neck Assembly Jig and cut the scarf joint. Remove the neck and sand the scarf joint on a stationary belt sander or smooth with a hand plane or sanding surfaces. Continue to assemble the neck as per the one-piece neck construction above.


Once the wood has been fabricated, be sure to align it an mark it clearly
with a dry marker (notice the black registration lines) laminations to
 decorate and strengthen the neck and cut them to proper length and height.
Glue all the pieces together and clamp to a flat surface.


Once the neck has been squared up, it is time to channel the neck to prepare it for your selected reinforcing method. There are many options available to the luthier and we cover many of them in this chapter. By keep the neck consistently square you can easily use a shaper or a router or even a tablesaw to cut the required channeling.

Glueup of Laminated NeckOnce the reinforcing has been installed and the surface of the neck has been leveled, it is time to install the headpiece veneer. My reinforcement of choice is Aircraft Aluminum, or T6 tempered aluminum. This is tough stuff and when it is epoxied into the center of your neck combined with the wood lamination that we talked about earlier in this article, you will have a neck that is hard to beat. For this reinforcement, be sure to visit our Aluminum Neck Reinforcement Product Page so you can use the same superior reinforcement that is used in all of my necks.

The uppermost headpiece veneer should be approx. 1/16" thick (1.5mm). This veneer more often than not matches the hardwood of the guitar back and sides, but occasionally it can be a feature veneer such as curly or bird’s eye Maple, Ebony, or other exotic wood species.

Additionally you can choose to build up several layers of alternating light and dark veneers giving a very nice layered look.

Another alternative is to trim the headpiece with either wood or plastic purfling by cutting a small channel with a dermal router after the veneers have been laminated and trimmed to the headpiece.

Note: This is an excerpt from our upcoming book: Ultimate Guitar Building - The Book.

To Learn more about this and much more about guitar and ukulele construction, take a look at our brand new eBook Guitar and Ukulele Construction Handbook